Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
Have you been searching for ideas concerning Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't precisely rocket science, yet it does require solid plumbing, carpentry, as well as often, tiling skills. Changing an old tub with a new one is likewise a moderately difficult job. If the old bathtub is readily obtainable, the project can move speedily; if you have to open up a wall surface to remove the old bathtub and also position the brand-new tub, the task is a lot harder. In either instance, the job is within a house handyman's abilities, although you will need a helper to leave the old tub and also set in the new one. See to it you have qualified yourself for the task as well as are comfortable attempting it. Rather than employing a service provider to take control of a halfway-completed job, it is better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This write-up will assist you mount a brand-new bathtub in your restroom if you have already bought a brand-new tub and do not need to alter the plan of your previous water pipes.
Your tools and also material checklist should consist of the following:
Planning for the Installation
To start with, the supporting structure provided with the bathroom should be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets system to stop pressure on the bath tub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its final setting.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water supply. After doing so, turn on the taps to drain any kind of water remaining in the system. The process of removing the existing taps can be fairly bothersome as a result of the limited access that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Prior to going on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Using the two wood boards under its feet, position the bathtub in the required position. The wooden boards are practical in equally spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four small points.
The following objective is to make sure that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the tub until the level checks out level.
To set up taps, fit all-time low of the outermost versatile tap adapter to the suitable supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the water as well as examine all joints as well as brand-new pipework for leakages and also tighten them if needed. Fill the bath tub as well as also inspect the overflow electrical outlet and the typical outlet for leakages.
Ultimately, repair the bathroom paneling as described in the maker's user's manual. Tiling and also sealing around the bathtub ought to wait up until the bathtub has been made use of at the very least when as this will resolve it right into its last setting.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines are in area between the faucet as well as the sink. Secure the faucet in place with the manufacturer provided backnut. As soon as the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former kind must be attached to the faucet ends first, tightening only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall in between the bathroom as well as the tiling, resulting in difficulties with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the tub with water before securing, to permit the motion experienced when the tub is in usage. The sealant can break rather early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our section on How to Install a Bathtub. Thanks for taking a few minutes to browse our content. Feel free to take the time to promote this post if you liked it. I am grateful for your time. Kindly come visit our blog back soon.
Appointment Report this page